|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Another excellent buy! A fully readable PDF archive. Good prints!!
;
It is wonderful done!!! a great job in scanning the manual. Superior quality in all the electric scheme. Very understandable and net!!! Thank you!
;
muy buen manual por lo completo de este algunos esquemas estan muy divididos lo que hace algo dificil el seguimiento.
;
very good manual, with detail and clarity in esquematic diagrams and waveforms .
;
Very quality copy of original service manual, which contains the circuit diagrams, PCB and lists of components, well as recommendation for calibration procedures of device, also everything else, that need for repair, tuning and use this oscilloscope.
All presented copies have high-resolution, so you can view all in detail.
This manual will very useful for simple owners and for repairers.
I recommend these manual, because myself is owner of Philips PM3216 and I need sometimes servicing these oscilloscope (principally calibrating).
Also, these document is an example of excellent design of technical documentation.
AV-28BT8ENS / AV-28BT8ENB / AV-28BT80EN AV-28BT8EPS / AV-28BT8EPB / AV-28BT80EP AV-28BT8EES / AV-28BT8EEB/ AV-28BS88EN
SPECIFIC SERVICE INSTRUCTIONS
DISASSEMBLY PROCEDURE
REMOVING THE REAR COVER
1. Unplug the power c ord. 2. Remove the 8 screws marked A as shown in the Fig. 1. 3. Remove the 4 screws marked B around the AV TERMINAL BOARD. 4. Withdraw the rear cover toward you.
CHECKING THE PW BOARD
To check the back side of the PW Board. 1) Pull out the PW Board. (Refer to REMOVING THE MAIN PWB). 2) Erect the PW Board vertic ally so that you c an easily check the back side of the PW Board. [CAUTION] " When erecting the PW Board, be c areful so that there will be no contacting with other PW Board. " Before turning on power, make sure that the wire connector is properly connec ted. " When conducting a check with power supplied, be sure to c onfirm that the CRT EARTH WIRE (BRAIDED ASS�Y) is connected to the CRT SOCKET PW board.
REMOVING THE AV TERMINAL BOARD
" Removing the rear cover. 1. Remove the 2 screws marked C fastened the AV TERMINAL BOARD. 2. Remove the AV TERMINAL BOARD.
REMOVING THE MAIN PWB
" Removing the rear cover. " Removing the AV TERMINAL BOARD. 1. Remove the 3 screws marked D as shown in the Fig.1. 2. Slightly raise the both sides of the chassis by hand and withdraw the MAIN PWB backward. (If necess ary, take off the wire clamp, connectors etc.)
WIRE CLAMPING AND CABLE TYING
1. Be sure to clamp the wire. 2. Never remove the c able tie used for tying the wires together. Should it be inadvertently removed, be sure to tie the wires with a new c able tie.
REMOVING THE SPEAKER
" Removing the rear cover. 1. Remove the 4 screws marked E, and remove speaker as s hown in Fig. 1. 2. Remove the speaker.
REMOVING THE FRONT AV & HEADPHONE PWB
" Removing the rear cover. " Removing the MAIN PWB. 1. Remove the 2 screws marked F. 2. Remove the FRONT AV & HEADPHONE PWB.
REMOVING THE FRONT CONTROL PWB
" After removing the rear cover . 1. Remove the MAIN PWB ASS�Y. 2. Remove the 5 screws marked G, and remove the FRONT CONTROL PWB.
6
No.52057
|
|
|
> |
|